Tools/Maintenance

Tri-Flow Superior Lubricant is a light viscosity lube that allows for deep penetration into hard to reach moving parts. - Ideal for all conditions - wet, dry, road and trail - High grade petroleum oils provide optimum lubrication under extreme temperatures (-60 to 475F) and humidity

The BKD-1.2 Hydraulic Brake Bleed Kit will bleed most models of DOT fluid-based hydraulic disc brakes, including models made by SRAM®, Formula®, Hayes®, and Hope®. Bleeding of hydraulic brakes removes air bubbles and contaminants from the braking system, for long-lasting components and peak performance. The BKD-1.2 is built for the rigors of daily commercial use and includes two syringes, hoses with shutoff clips, multi-size bleed blocks, and a set of our unique mountable syringe holders, as well as multiple hose fittings to fit the multiple standards found on hydraulic bicycle brake systems. Every part is replaceable and available from Park Tool. Housed in a rugged storage case. Includes: - Two 20 mL syringes Two hose assemblies with shutoff clips - Two 10 mm/12 mm universal bleed blocks - Two 11 mm bleed blocks for Hayes® systems -  Two adjustable syringe holders -  M5 x 0.8 adapters— SRAM® (x2) -  M6 x 1.0 adapter— universal (x2) - Bleeding Edge-specific fitting — SRAM® -  Hose compression sleeve — universal -  Set of spare O-rings and hose -  Replacement parts available -  Brake fluid not included NOTE: The BKD-1.2 is for DOT fluid-based hydraulic bicycle brake systems only. DOT fluid and mineral oil should never be mixed in the brake system or in their respective service tools. Cross-contamination of brake fluid may cause seal failure which may result in brake failure. For mineral oil brake systems use the Park Tool BKM-1.2 Hydraulic Brake Bleed Kit — Mineral Oil.

With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The TW-6.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). Designed for higher torque settings for repairs and installation in the bottom bracket, cassette lockring and other areas that use a higher torque settings. For lower torque setting, see the TW-5. Comes with its own protective case. - 10–60 Newton meter range (88–530 Inch Pounds) - Adjustable in 0.25 Nm increments - Ratcheting 3/8" drive - Reads and registers for both left hand and right hand threading - Dial-adjust system allows desired torque setting to be preset - Calibrated to be accurate to +/- 4% - Length: 36.2cm (14.25")

Take the guesswork out of installing cables, wires and housing inside the frame. The IR-1.2 speeds the internal frame routing of electric wires, shift cable/housing, brake cable/housing and hydraulic tubing on carbon fiber, titanium, and aluminum frames. Kit includes four plastic-coated 250cm cables with attached magnets and unique fittings plus an external guide magnet to speed operation. Newly updated to include a dedicated E-tube Di2 cable connector that easily pulls through a 6mm frame hole. Opposite polarity magnets on cables seek and attach inside frame tubes, making it easy to route through frame entrances and exits. Works with any size frame including tandems. A true time and frustration saver!

When a flat strikes, this organized kit will get you rolling in no time. Kit Includes: - Control Blast 0 Inflator Head - Mtb Kit: (65067) 2, 25G Threaded Co2 Cartridge - Road Kit: (65066)2, 16G Threaded Co2 Cartridge - Ratchet System Multi-Tool (2, 2.5, 3, 4, 5 ,6Mm Hex, T10, T25 Torx And Flathead) - Giant tire levers

BB30 service kit for SRAM DUB cranks. - Includes (2) Enduro 6806/29 ABEC-3 sealed bearings and 2 retaining clips - Bearing Dimensions: OD: 42mm / ID: 29mm / Width: 7mm - Enduro ABEC-3 bearings - Use with SRAM DUB cranks Note: SRAM DUB cranksets are not designed to work in 68mm or 73mm wide shells with inboard bearings. Use only if your frame is a direct-fit bearing system, and the BB shell width is 86.5mm or wider.

These professional-grade screwdrivers are designed for ease of use, comfort, and lasting durability. - Five-Piece Set Includes: #1 and #2 Phillips plus 4.5, 5.5, and 6.5mm flat-blade screwdrivers and storage pouch. - Two-Piece Set Includes: #2 Phillips and 5.5mm flat-blade screwdrivers - Dual-density, ergonomic thermoplastic handles for comfortable grip and leverage. - Heat-treated tool steel construction for strength and durability.

Never leave safety behind. Topeak's Mini 18+ folding tool lets you take it all with you without weighing you down. Its forged-aluminum body holds 18 tools including: 2, 2.5, 3, 4, 5, 6, 8 and 10mm Allen wrenches, a T25 Torx wrench, 14- and 15-gauge spoke wrenches, a cast-chromoly chain tool, aluminum tire lever, Phillips and flat-blade screwdrivers, and a bottle opener.

Finish Line® Dry Lube is the bicycle industry's original and most versatile dry-style chain lubricant. It is formulated with high-performing nano-ceramic boron nitride. This Non-Stick Ceramic Technology is 100% fluoro-free and sets up with a dry ‘wax-like’ film. It attracts less grime and delivers a low coefficient of friction over long re-lubrication intervals. It is ideal for riding on or off-road, in dry, dirty, dusty environments, and also holds up well in wet conditions. Designed for chain applications, it can also be used on derailleurs, shifters, cables, and brake pivot points. Dry Lube delivers optimum drivetrain efficiency without attracting excessive amounts of abrasive contaminants. • Formulated with Non-Stick Ceramic Technology • Lowers friction, improves pedaling efficiency, reduces wear • Quickly sets up dry and clean • Minimizes the attraction of abrasive contaminants • Low surface tension easily penetrates chain pins • Biodegradable and 100% fluoro-free

- CNC side panels with a lightweight, easy to carry, ultra-compact design - 8mm hex bit combines easily with 5mm allen wrench - Independent valve core tool - CO2 inflator tool - Tools: 2, 2.5, 3, 4, 5, 6, 8mm Hex, PH2, T25, SL5, Valve Core Tool, CO2 inflator - Sizes: 88 x 54 x 8mm (TBC) - Weight: 114g

The Problem Solvers Through-Axle adapters make it possible to easily fit front and rear wheels with through axles into truing stands for wheel truing and repair. These adapters fit into the common through-axle sizes and have o-rings so that they fit nicely and stay put as you work on the wheel and take it in and out of the stand. They're made of CNC-machined 6061 aluminum for quality and durability. - Front compatible with 9/15/20mm hubs - Rear: compatible with 10/12mm hubs

For extreme conditions, you need an extreme lube. That's when you grab Finish Line's Wet Lubricant. It's ultra water-resistant and long-lasting thanks to its special formulation of synthetic oils, special polymers and anti-wear additives. This lube delivers superb drivetrain lubrication and protection and it's the ultimate choice for muddy off-road rides, all-day epics and long, rainy commutes. - Formulated with high viscosity synthetic oils, water repelling polymers, and advanced anti-wear additives - Will require more attention to drivetrain cleanliness, but delivers the ultimate in lubricity and protection - Upon application, wipe excess off chain to minimize attraction of dirt and grime - Finish Line's Wet Lubricant delivers the ultimate in lubricity and protection. It requires a little more attention to drivetrain cleanliness compared to Finish Line's Dry or Wax lubes.

Protect your clothes while looking pro with Giant's Shop Apron. It's made from tough, heavy-duty 10-ounce material with an embroidered Giant logo. Unlike standard aprons, Giant's uses a unique strap system to take the weight off your neck and puts it on your strong shoulders. And off course it has roomy pockets to hold frequently needed tools.

Park's Mini Chain Brute Chain Tool goes anywhere and features a V-shaped handle, a super-strong replaceable pin, and fine threads to make chain removal and installation a breeze. The CT-5 works on any derailleur chain, including Shimano Hyperglide and 9-, 10-, and 11-speed. It works for loosening tight links, too.

Park's Crank and Bottom Bracket Wrench is perfect for working on old-style bottom brackets. The HCW-4 utilizes a 36mm box-end head and a pin spanner for your bottom bracket removal and installation needs.

Cleans bicycle chain quickly, easily, and effectively — without the hassle and mess of removing the chain from the bike. The Cyclone uses a large solvent reservoir, hundreds of rotating bristles, and a two-step cleaning process to get chains really clean, improve shifting performance, and extend the life of the chain and other expensive drivetrain parts. - Works with all multi-speed bikes (5, 6, 7, 8, 9, 10, 11, and 12-speed) as well as some single-speed models and e-bikes - Strong magnet at the bottom of the fluid reservoir holds metallic particles scrubbed from the chain - Special wicking sponge draws solvent from the chain as it exits, minimizing drips and mess - Sturdy handle makes the Cyclone easy to use and control - Holds 2 fluid ounces (59ml) of solvent

Park's Needle Nose Pliers are professional quality, 6-inches long, and made from forged, heat-treated chromoly steel. For ease of use they have a hidden spring, cutting jaws and 5 different gripping and crimping areas. Plus, they have soft-touch, dual-density handles for an excellent grip.

Park's Shop Hammer is designed specifically for use on bicycles. It features a unique dual-sided head with both steel and plastic striking surfaces, a reinforced fiberglass shaft and a soft, comfortable molded handle. The HMR-4 proves that sometimes a hammer is the best tool for the job.

- Giant Torqkey w/ Bit Storage - Available in 4Nm, 5Nm, and 6Nm

Forged and machined, the ZP-5 is ideal for closely cutting zip ties and many other materials in tight spaces.

The Birzman Housing and Cable Cutter provides great handling comfort and is designed to offer additional leverage strength. The integrated awl helps restore cut housing ends, clearing the way for smooth cable operation.

Precision CNC machined aluminum tool for the installation and removal of 16-notch external bearing bottom brackets. Featuring updated tooth profiles to optimize the fit between the tool and high performance BB parts. Anodized and laser engraved for easy identification and featuring a ratchet/torque wrench compatible 3/8-inch drive. - 16-notch 39mm OD cups - Fits: Shimano XTR BB93, Dura-Ace BB9000, Token - Added depth to fit Shimano STEPS square drive motor

A precision CNC-machined aluminum tool for the installation and removal of select threaded bottom brackets with 12-notch tool fittings, including Praxis Works® M30 bottom brackets. Manufactured in-house by Park Tool, anodized for easy identification and featuring a ratchet/torque wrench-compatible 3/8" drive. Fits 12-notch bottom bracket tool fittings with a major diameter of 48–50 mm and a minor diameter of 46.3 mm, including: - Praxis Works® M30

Forged and precisely machined, the high leverage LP-7 Utility Pliers include an integrated cutting blade and soft touch grips.

Keep your Reverb dropper post performing at its best with RockShox's Reverb Hydraulic Fluid. It's optimized for the remotes of the Reverb as well as the Monarch XX rear shock.

Never leave safety behind. Topeak's Mini 9 folding tool lets you take what you need and won't weigh you down. Its forged-aluminum body holds 9 tools including: 2, 2.5, 3, 4, 5, 6 and 8mm Allen wrenches, a T25 Torx wrench and a Phillips screwdriver. Plus this smart tool tucks neatly into its included neoprene case.

Sliding T-Handle Torx Wrench - Updated design features increased tip and head clearances, improved indexing, large easy-to-read size marking, and color bands for quick size identification. - Premium S2 tool steel construction and three precision tips ready to tackle any task. - Three-position sliding t-handle design and extra-long extended leg offer the ultimate in speed, ergonomics, leverage, and versatility. Pedro's Master T Handle wrenches have quickly become a favorite of elite mechanics around the world. With a solid foundation to build on, each wrench has been redesigned from the ground up. The new wrenches feature unmatched tip and head clearances, improved sliding T indexing, large easy-to-read size markings, and color bands for quick wrench identification.

Finish Line's Premium Grease With Teflon is a race-proven lubricant formulated for the unique demands of bicycle bearings. It's exceptionally strong and thick, it doesn't separate and it repels water even when submerged. Additionally, it's very slick and tough and lasts as much as five times longer than petroleum grease.

Forged with Chrome Vanadium (CR-v) steel, precision ground, heat-treated, plated and polished. The PAW-6 opens to 24mm and features a laser engraved measurement scale and dipped blue handle for comfort.

Made from high precision, hardened Cro-Moly steel, Park's Bottom Bracket Tool (External Bearing) can be turned with a 3/8" drive wrench, 1" wrench, or Park Tool FRW-1 Freewheel Remover Wrench (each sold separately).